How to tell if PPF is installed correctly: a 12-point inspection checklist
Most people collect the car and drive away, then notice issues a week later. It is better to check while you are still at the shop, because a fix is easier then and the shop sees the issue with you.
How to check: in strong light, or take the car out into the sun. Look at each panel from a shallow angle rather than straight on, because defects show in the reflection. Walk round the car slowly.
First: what is normal after installation?
These are normal and clear on their own within 1 to 4 weeks:
- Small water bubbles under the film. They look like damp spots and shrink every day.
- Slight haze in some areas.
- Moisture lines near the edges.
The film is fitted with water and soap, and that moisture leaves through the film over time. In humid cities it takes longer.
The checklist
1. Edges
Run your eye along the edge of every piece. It should be stuck down and flat. An edge that is raised, or moves when touched gently, needs fixing before you leave.
2. Corners and sharp ends
Bumper corners, bonnet tips and mirrors are the hardest places. Check that the film wraps them well, with no small puckers ("fingers") at the corner.
3. Air bubbles
An air bubble differs from a water bubble: it looks clearer and empty, and does not shrink over the days. It will not go on its own.
4. Contamination under the film
A speck of dust, a hair, or a small raised dot under the film. One or two tiny specks on a whole car happen even at excellent shops. Many of them, or an obvious one in the middle of the bonnet, mean the bay was not clean.
5. Stretch marks
When film is stretched beyond its limit it shows faint lines or a distorted reflection, visible from a shallow angle. Over-stretched film also has weakened adhesive and tends to shrink back from the edge over time.
6. Adhesive marks
Dull lines or patches under the film that do not move or shrink. They usually come from lifting and re-laying the film several times during fitting.
7. Cut alignment
With computer-cut film, look at the gap between the film edge and the panel edge. It should be even along the edge and on both sides. A wide gap on one side and a narrow one on the other means poor alignment.
8. Blade marks
The most serious defect. If the film was hand-cut on the car, inspect the paint along the film's edges and around badges, handles and sensors. A fine line in the paint following the film edge means the blade reached it. Replacing the film does not fix that, so record it with the shop immediately, with photos.
9. Seams
Large panels are sometimes covered in two pieces. Ask beforehand where seams will be. At handover, check that each seam is straight, clean and somewhere unobtrusive.
10. Sensors, cameras and badges
Make sure parking sensors, radar and cameras are uncovered or neatly cut round, and that they work. Test them before you leave.
11. Parts that were removed
If the shop removed badges, handles or lights, check that they are back in place, firm and level, with no gap against the body.
12. General cleanliness
No dried soap residue, no fingerprints under the film, and no new scratches on uncovered paint.
What to do if you find something
- Photograph it: one close-up and one showing where it is on the car.
- Show the shop before you leave and ask whether it will clear on its own or needs fixing.
- If they say it will clear, ask for a check appointment in two weeks and write it down.
- A good shop fixes installation issues free of charge.
A second check after 2 to 4 weeks
Go over the same points again, focusing on:
- Have the bubbles and haze gone?
- Has any edge lifted after the first wash?
- Has any discolouration or mark appeared that was not there before?
Whatever has not cleared after a month will not clear on its own. Go back to the shop with your first photos.
When is an issue "acceptable"?
Installation is manual work and perfection is hard. Generally acceptable: one or two tiny specks visible only up close, and a visible film edge on computer-cut pieces. Not acceptable: lifted edges, air bubbles, obvious stretch marks, a lot of contamination, and any blade mark on the paint.
After collection, follow the aftercare guide, especially the first-week instructions.
Frequently asked questions
How do I know if my PPF was installed correctly?
In daylight, check that every edge is flat and stuck down, corners are wrapped without creases, there are no air bubbles or visible specks in the middle of panels, no stretch lines when you look at an angle, and no cut marks on the paint at the edges.
Are small bubbles normal after PPF installation?
Small water bubbles or a slightly hazy look are normal for days to a few weeks while the film dries, and they shrink on their own. Air bubbles that do not shrink are a defect.
When should I check PPF after installation?
Twice: at handover before you drive away, and again after 2 to 4 weeks, when the film has dried and lifting edges or leftover bubbles show up.







